A REVIEW OF HIGH-PRESSURE WATER-DRIVEN VALVE ACTUATORS: MECHANISMS, CYLINDERS, MATERIALS, AND SEALING TECHNOLOGIES
Keywords:
Water hydraulics, Water-driven valve actuator, High-pressure water, Gear-rack rotary actuator, Material selection, Surface engineering, Sealing technology, Friction and wearAbstract
The shift towards sustainable and environmentally friendly industrial technologies has spurred a significant resurgence of interest in water hydraulics, particularly for high-pressure applications in sensitive environments such as nuclear power, food processing, and underwater robotics. This review examines high-pressure water-driven valve actuators, focusing on the design, materials, and sealing technologies of the driving cylinders. Gear-rack actuators serve as the primary case study, reflecting their widespread use in quarter-turn valve service, and are compared with alternative rotary and linear actuation mechanisms. The paper analyzes the challenges posed by water as a working fluid, including its low viscosity, poor lubricity, and high corrosivity, and surveys current solutions in material science and surface engineering. A detailed analysis covers the selection of materials for cylinders and rods, the application of surface coatings such as Diamond-Like Carbon (DLC) and nano-composite CrN (CNC) for wear and corrosion resistance, and the development of sealing technologies. The review places particular emphasis on seal material compatibility, with a comparative analysis of elastomers such as Nitrile Rubber (NBR), Fluoroelastomer (FKM), Ethylene Propylene Diene Monomer (EPDM), and Perfluoroelastomer (FFKM), and the adoption of advanced polymers such as Polyether Ether Ketone (PEEK) and filled Polytetrafluoroethylene (PTFE). By synthesizing recent research and engineering practice, this paper is intended as a reference for researchers and engineers working on high-performance water hydraulic systems.References
[1] Li Z Y, Yu Z Y, He X F, et al. The Development and Perspective of Water Hydraulics. Proceedings of the JFPS International Symposium on Fluid Power, 1999, 1999(4): 335-342.
[2] Yang X, Wu D, Gao H, et al. Position Control of Water Hydraulic High-Speed On-off Valves-Controlled Cylinder of Water Hydraulic Manipulator. Nuclear Engineering and Design, 2025, 442.
[3] Lalaklo A H, Semproni F, Iacovacci V, et al. BiFlu2: A Miniaturized Electro-Fluidic Circuit for All-On-Board Control of Hydraulically-Actuated Biorobotic Organs. 2025 IEEE 8th International Conference on Soft Robotics (RoboSoft), 2025.
[4] Zhu J A, Guo P H. Developing History of Water Hydraulic Technology and its Application in Coal Mine Production. Applied Mechanics and Materials, 2011, 42: 236-241.
[5] Li Q. Eco-friendly Optimization Strategies for Water Hydraulic System Design in Environmental Engineering for Enhanced Sustainability. Natural and Engineering Sciences, 2025, 10(3): 463-474.
[6] Pobedza J, Sobczyk A. Properties of High Pressure Water Hydraulic Components with Modern Coatings. Advanced Materials Research, 2013, 849: 100-107.
[7] Li R, Wei W, Liu H, et al. Tribological Behavior of Tribo-Pairs in Water Hydraulic Radial Piston Pumps. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2023, 237(7): 1603-1623.
[8] Yoshimura S, Nakamura Y, Noda T, et al. Series Elastic Actuated Needle Valve and Sealing Equilibrium Flow Rate Models for Precise Position Control in Single-Acting Water-Hydraulic Actuators. 2026 IEEE/SICE International Symposium on System Integration (SII), 2026: 850-855.
[9] Ikeo S, Ito K, Ochiai T. Research on High Speed Drive of Water Hydraulic Cylinder. Proceedings of the Sixth International Conference on Fluid Power Transmission and Control, 2005: 208-212.
[10] Pustavrh J, Trajkovski A, Tic V, et al. Analysis of Different Guide Elements’ Designs in Hydraulic Cylinders. Applied Sciences, 2025, 15(9).
[11] Zhang D, Luan B, Chen F, et al. Failure Analysis and Structural Design Improvement of Support Device for Heavy-Duty Rack and Pinion Hydraulic Actuator. Scientific Reports, 2026, 16(1).
[12] Song J, Dong C, Bai X, et al. Tribological Characteristics of Rotary Vane Steering Gear Seals Under the Oil With Different Abrasive Particle Sizes. Tribology Transactions, 2023, 66(6): 1128-1138.
[13] Sotoodeh K. Actuator Selection and Sizing for Valves. SN Applied Sciences, 2019, 1(10).
[14] Güngör O. An Approach for Optimization of the Wall Thickness (Weight) of a Thick-Walled Cylinder Under Axially Non-Uniform Internal Service Pressure Distribution. Defence Technology, 2017, 13(3): 150-157.
[15] Liu T W, Shang Y X, Li Y, et al. A State-of-the-art Review on Lightweight Composite Hydraulic Cylinders: Design, Manufacturing and Applications. Composite Structures, 2026.
[16] Skowrońska J, Kosucki A, Stawiński Ł. Overview of Materials Used for the Basic Elements of Hydraulic Actuators and Sealing Systems and Their Surfaces Modification Methods. Materials, 2021, 14(6): 1422.
[17] Deshwal D, Belgamwar S U, Bekinal S I, et al. Role of Reinforcement on the Tribological Properties of Polytetrafluoroethylene Composites: A Comprehensive Review. Polymer Composites, 2024, 45(16): 14475-14497.
[18] Kayser H. Energy Generation from Sea Waves. Halifax, 1974: 240-243.
[19] Zhang X, Fan X, Liang J, et al. Experimental Study on a Three-Position Four-Way Water Hydraulic Directional Valve with a Novel Sealing Structure. Scientific Reports, 2025, 15(1): 20561.
[20] Huang W, Pan Z, Guo C, et al. A Multi-Degree-of-freedom Water Hydraulic Manipulator in Nuclear Applications: Design and Experiments. Fusion Engineering and Design, 2025, 219.
[21] Chen G, Yang X, Zhang X, et al. Water Hydraulic Soft Actuators for Underwater Autonomous Robotic Systems. Applied Ocean Research, 2021, 109.
[22] Chen C, Shi W, Xian T, et al. Theoretical and Experimental Study on Pressure Pulsation Energy Harvesting in Water Hydraulic Systems. 2023 9th International Conference on Fluid Power and Mechatronics (FPM), 2023: 1-8.